whirlpool direct drive washer error codes

Make sure the drain hose is not pinched or stopped up. Re-select cycle and press START.

How To Reset Whirlpool Front Loader Washer Step By Step Machinelounge

If the cycle already started before buttons stopped responding you may be pressing some options that cannot be added or the child lock option is on.

. The first thing to do is as usual rebooting your machine. LF in the display. Clean out your drain pump filtercoin trap and drain pump.

How to enter diagnostics. Press and hold the Control Lock button down for 3 seconds. Unable to select certain options.

Whirlpool Washer Front Loader E01 F09 Error Code Wont Drain Spin Here is the link to what we bought. The information on this site is intended for qualified service technicians and technically knowledgeable audience. During this time the washer pauses the tumbling and adds water for additional rinsing.

If your fill hoses have a flood stop check valve turn the water off disconnect the hoses and run a little water into a bucket. Be sure the drain pump is operating properly. You can try resetting the machine to release the lock or explore several mechanical components that can be the cause.

Unplug the device and check the hosepipe. In case it is not that easy start inspecting the drain system of your device. The LoC or LC codes will appear if you try to push the interface buttons.

Check the water level pressure hose from the water level pressure sensor to the air trap on the. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test. If the lid is actually being opened between cycles but the control does not detect it then the door lockswitch assembly will normally need to be replaced.

There are some obvious explanations for the drainage system error such as the clog of one of its elements of the failure of the drainage pump. We paid for our own parts this isnt a affiliate link. This Duet Washer Diagnostic Guide is for the following core washer models WFW70HE WFW80HE WFW81HE WFW94HE WFW95HE WFW96HE WFW97HE Non Steam.

When Sud or Sd is displayed the washer automatically extends the rinse time to remove the excess suds. The washer will not be able to spin out water with the excess suds. When LF is displayed there could be an issue with the water flowing into the machine.

I press Wash Setting and Spin 3x the f3 e1 blinking I click the power button it does not turn off. If you are lucky the code will disappear from the screen and the machine will start operating normally. Unplug the washer for 30 seconds to attempt to reset the Duet washer control.

If all else fails you can pop the door open manually whether its a top-loading or front-loading machine. All communications are opinions only and should not be considered a replacement for professional advice andor service. 22 rows This site uses cookies to improve your experience.

The Start and Power buttons will still be active. The information on this site is intended for qualified service technicians and technically knowledgeable audience. Check your home water valves.

Can you kindly please on. Buttons Wont Respond. Select DRAINSPIN if there is excessive water in the washer.

15 rows Nowadays almost all the new washing machine models are equipped with the self. Whirlpool WFW75HEFW washing machine. Make sure the water inlet valve is not allowing water in the unit when not in operation.

All communications are opinions only and should not be considered a replacement for professional advice andor service. If your Whirlpool washer door is locked and the light is flashing there are a few possible causes and fixes. F codes other than F20 F21 or F22.

Up to 32 cash back If the washer is started several times without the lid ever being opened then this code appears. 15 rows Press POWER and select START. Check the water inlet hoses to be sure they are not clogged or kinked.

There will be an indication counting down to the lock activation. Give it a rest for 10-15 minutes and switch it back on. This pause allows the bubbles in the suds to break.

Learn how to adjust your settings. If the problem remains call for service. What can cause the DR Error.

Select PAUSECANCEL twice to cancel the cycle. These codes are a reminder that you need to deactivate the control lock.

Whirlpool Belt Drive Washer Repair Guide Applianceassistant Com Applianceassistant Com